REGUPOL SONUS 12MM UNDERLAYMENT

$2.48

Availability: In stock





































Regupol Sonus Roll - 12 mm
Is a high performance acoustic underlayment designed to reduce the transmission of impact sound caused by people walking. The Regupol Sonus can be installed under ceramic tile, stone, carpet, carpet tile, and hardwood flooring.
ADVANTAGES:   Sustainable green product made from post-consumer and post-industrial waste, including recycled tires. Greatly reduces sound transmission of impact noise. Acoustic ratings up to STC 66, IIC 74, Delta IIC 27 depending on the floor covering and floor-ceiling assembly. Multiple sizes available including 2mm, 3mm, 5mm, 6mm, 10mm, and 12mm thicknesses.
PRODUCT SIZE:   4' x 25' – 100 sq. ft. per roll.
WHERE TO USE:   Apartments. Condominiums. College dormitories. Class rooms. Schools. Hospitals. Any area where reduction of impact noise is desired.
USED UNDER:   Carpet. Tile. Stone. All kinds of hardwood or laminate flooring.
*Sold by feet.

  •   internetsales@ramosdecorandlumber.com

       1.800.897.2667

    *Certain restrictions apply:
    Regarding purchases and shipments of doors, moldings, cabinets and machines, please contact us.

     

     

    Product Description

    Regupol Sonus - Sound Control Underlayment - HS1200
    Are high performance acoustic underlayments designed to reduce the passage of impact sound transmission caused by people walking and can be installed under ceramic tile & stone, carpet & carpet tile and hardwood flooring. Regupol Sonus products are GreenCircle certified for recycled content and can qualify for potentially 8 LEED points, making Regupol underlayments the preferred choice for impact sound control applications in acoustic and vibration control.

    ADVANTAGES:

    • Sustainable green product made from post-consumer and post-industrial waste, including recycled tires
    • GreenCircle certified and can potentially qualify for up to 8 LEED points
    • Greatly reduces sound transmission of impact noise
    • Acoustic ratings up to STC 66, IIC 74, Delta IIC 27 depending on the floor covering and floor-ceiling assembly
    • Multiple sizes available including 2mm, 3mm, 5mm, 6mm, 10mm, and 12mm thicknesses.

    HOW TO USE IT:
    Regupol Sonus Underlayment and the flooring material must acclimatize, in their sealed packaging, in the room where they are installed for at least 48 hours, at temperature of at least 65ºF. Before starting installation make sure the sub floor is permanently dry and free of dirt, dust, grease and other foreign matter. Concrete must be free of efflorescence and not subject to hydrostatic pressure. Sub floor moisture percentages should not exceed the flooring manufacturers or Regupol’s recommendations of 5 pounds per 1,000 square feet over 24 hours or RH at 85%.

    Wood Floor Construction: Sub floor should be properly leveled, structurally sound and clean. Plywood sub flooring should be of a good grade. Variations in floor level over 1/8” within 3 feet span should be leveled before installing underlayment. Any nails or other protrusions should be pounded flat or removed. Sub floor should have L360 for deflection.

    Concrete Slab: Inspect concrete sub floor for any open cracks and fill with a high grade patch. Remove any excess concrete lumps or residue that may interfere with the installation of Regupol Sonus. The concrete slab should be permanently dry. A good quality concrete waterproof sealer may be required if moisture in slab is too high.

    Installation of Tile: Regupol Sonus underlayment needs to be adhered to the sub floor. Acceptable bond-coat adhesives: Regupol TRUESET use 1/16” x 1/16” x 1/16” square– notched trowel (note a larger trowel size may be required based upon site condtiions). Periodically check and see that you are getting 100% transfer of adhesive. Start in a corner and roll out Regupol Sonus installing it flush to the walls. Roll up the roll halfway and apply adhesive on exposed area, roll back over adhesive flat trowel any air pockets, continue with other side the same way. Continue rolling out and gluing down Regupol Sonus in the same manner until the entire area is covered. Make sure the edges are tightly butted together, both side by side & end by end. Use a 50—100 lb roller to fully bond the Sonus to sub floor. Install perimeter isolation strips vertically on walls or leave a 3/16” gap around all perimeter walls (this gap can be filled with a latex caulk but NOT grout). After 8 hours or when adhesive is fully cured install tile/ stone flooring using a latex modified thin set (we recommend Laticrete 254). The thin set must be burned or keyed into the Sonus to insure proper bond. Grout and trim isolation material flush with floor, hold trim board 1/16” off floor to avoid flanking paths.

    Installation of Hardwood: 1. Glue Down Hardwood - Regupol Sonus underlayment needs to be adhered to the subfloor. Recommended adhesive: Regupol TruBond. Use 1/8" x 1/8" x 1/8" sq.– notched trowel (check for 100% transfer of adhesive and adjust to a larger trowel size if conditions require it). Install Sonus rubber in opposite direction to the hardwood floor. Start in a corner and roll out Sonus rubber installing it flush to the walls. Roll up the roll halfway and apply adhesive on exposed area, roll back over adhesive flat trowel any air pockets, continue with other side the same way. Continue rolling out and gluing down Sonus in the same manner until the entire area is covered. Make sure the edges are tightly butted together, both side by side & end by end. Use a 50—100lb. roller to fully bond the Sonus to sub floor. After 8 hours or when adhesive is cured install engineered hardwood flooring using Regupol WoodBond Urethane adhesive or recommended and approved adhesive (contact Regupol for list) and follow manufactures written instructions. Install baseboard slightly off floor to avoid flanking path. 2. Floated Hardwood Installation - Install Sonus rubber in opposite direction to the hardwood floor. Start in a corner and roll out Sonus installing it flush to the walls. Continue the next row in the same manner until the whole room is covered. You can tape the seams but it is not necessary. Install the floated engineered hardwood per manufactures written instructions. Install baseboard slightly off floor to avoid flanking path.

    COLOR:   Black.   PRODUCT FORM:  
    Roll.
     
    PRODUCT SIZE:   4' x 25' – 100 sq. ft. per roll.   USED UNDER:   Carpet. Tile. Stone. All kinds of hardwood or laminate flooring.  
    DENSITY:   43 lbs cubic ft    ACCESORIES:   Tile - Trueset and ISO-Strip. Hardwood: TruBond, WoodBond ans ISO Strips.  
    HARDNESS:   40 - 55.   WHERE:   Apartments. Condominiums. College dormitories. Class rooms. Schools. Hospitals. Any area where reduction of impact noise is desired.  

    Additional Information

    SKU 30154
    Model# HS1200
    Manufacturer REGUPOL
    Shipping Weight 2.5000

    Product View - Custom Info

    This is a custom CMS block. You can use it to display information about shipping, returns, refunds, latest promotions etc. Put any content you want here, like text, HTML or images. There are many useful blocks like this one across the theme. All CMS blocks are editable from the admin panel.

    Shipping: Please allow about 5-10 business days for delivery. For delivery to Alaska or Hawaii, please allow 10-15 days for delivery. For delivery to PO Boxes in Alaska, Hawaii, US Territories and APO/FPO addresses, allow three weeks for delivery.

    Backorders: All backordered items will be shipped via Standard Delivery service at no additional charge.

    Returns Policy: You may return new, unworn or unused products within thirty (30) days of delivery for a full refund of the cost of the goods, or an exchange if preferred.

    Product Tags

    Add your tags

    Use spaces to separate tags. Use single quotes (') for phrases.