POLYURETHANE VARNISH SATIN 1 QUART

$18.50

Availability: Out of stock












































Super Polyurethane Clear Varnish - Satin - Wood Finish
One-step application for an extra-tough finish on interior/exterior wood and metal surfaces, protects against wear, abrasion, water and chemicals; clear and non-yellowing. Lead-free and 100% U.V. resistant; dries in 30 minutes to an extremely durable, tough and flexible finish.
BASIC USES:   Quickly renews old, dull and worn surfaces such as furniture, doors, woodwork, cabinets, etc.  Recommended for floors.
COLOR:   Clear
SURFACES:   Wood. Metal
DRYING TIME:   To touch: 1 hour. To recoat: 12 hours
SURFACE PREPARATION:   Dry, clean and free of contaminants such as dirt, grease, chalk, mildew, oil, rust, loose or badly cracked paint.
FINISH:   Satin.

  internetsales@ramosdecorandlumber.com

   1.800.897.2667

*Certain restrictions apply:
Regarding purchases and shipments of doors, moldings, cabinets and machines, please contact us.

 

 

Product Description

Super Polyurethane Clear Varnish -  Wood Finish
A special formulation of extra tough, one-component polyurethane finish for a one-step application on exterior or interior wood and metal surfaces that protects against wear, abrasion, alcohol, water and household chemicals while accenting the natural beauty of the wood grain. Lead-free formula is safe for children’s furniture.  Available in gloss (PV-357) and satin (PV-359).

ADVANTAGES:

  • 100% transparent
  • One-component
  • Non-yellowing
  • Lead-free
  • 100% UV resistant
  • Fast-drying
  • Tough and flexible
  • Extremely Durable

BASIC USES
To seal new or previously varnished wood on exterior and interior surfaces. Quickly renews old, dull and worn surfaces such as furniture, doors, woodwork, cabinets, etc.  Recommended for floors.

HOW TO USE IT
Apply by brush or roller, use LANCO® All Purpose Roller 3/8” Nap PA-566 or conventional or airless spray.  Roller application may require special care to prevent bubbling and more than one coat to obtain proper thickness.  Apply at 4 mils wet film thickness that will yield 2 mils dry film thickness.

Apply in good weather when air and surface temperature are above 40ºF and surface temperature is at least 5ºF above the dew point.  For optimum application properties, material should be between 70º to 100ºF prior to mixing and application. Recommended for floors only when high traffic areas are covered with rugs or carpets.

Surface Preparation: All surfaces must be dry, clean and free of contaminants such as dirt, grease, chalk, mildew, oil, rust, loose or badly cracked paint. 

New Wood: Sand down to a smooth finish with fine sandpaper following the grain.  Remove all sanding dust by vacuuming or dusting the surface with a “tack” cloth.  Fill knot holes and cracks with LANCO® putty filler for wood; let dry.  Sand the filled areas smooth and remove dust.

Cleanup: Wipe up drips and spatters with LANCO® Mineral Spirits MS-107.  Clean all equipment with this solution.

Equipment: Conventional Spray: For suction feed, use DeVilbiss MBC gun with “E” tip and needle and 30 air cap or equivalent at 35-40 psi atomizing pressure feed.  For pressure feed, use DeVilbiss MBC gun with tip and needle and 704 air cap or equivalent at 35-40 psi atomizing pressure and 5-8 psi fluid pressure, 3/8” ID material hose, double regulated pressure tank with oil and moisture separator. Airless Spray: Minimum  of 28:1 ratio pump, .011”-.013” orifice tip 1/4” ID Teflon material hose.

Caution: Do not take internally.  Close container after each use. Keep out of the reach of children.  Combustible; keep away from heat and open flame. Avoid prolonged contact with skin and breathing vapors or spray mist.

COLOR:   Clear.   DRYING TIME:  
To touch: 1 hour. To recoat: 12 hours.
 
PRODUCT SIZES:   55 GALS. 5 GALS. 1 GAL. 1QT.   SURFACE:   Wood.  
THINNING:   Not normally recommended, but if necessary, add up to 1/2 pint per gallon of LANCO® Mineral Spirits MS-107.   FINISH:   Satin.  
PRECAUTION:   Flammable.   COVERAGE:   600 sq. ft./gal.  

Additional Information

SKU 16407
Model# PV-359-5
Manufacturer LANCO
Shipping Weight 0.0000

Product View - Custom Info

This is a custom CMS block. You can use it to display information about shipping, returns, refunds, latest promotions etc. Put any content you want here, like text, HTML or images. There are many useful blocks like this one across the theme. All CMS blocks are editable from the admin panel.

Shipping: Please allow about 5-10 business days for delivery. For delivery to Alaska or Hawaii, please allow 10-15 days for delivery. For delivery to PO Boxes in Alaska, Hawaii, US Territories and APO/FPO addresses, allow three weeks for delivery.

Backorders: All backordered items will be shipped via Standard Delivery service at no additional charge.

Returns Policy: You may return new, unworn or unused products within thirty (30) days of delivery for a full refund of the cost of the goods, or an exchange if preferred.

Product Tags

Add your tags

Use spaces to separate tags. Use single quotes (') for phrases.